I recently purchased a dip28 socket of programing 27C512R chips but I can't get the xport to recognize them.
I get the same thing when I try to use 27C040 or 27C020 chips.
I'm running the latest build (624) from march.
Here's my console script.
FlashcatUSB Script Engine build: 310
Welcome to the FlashcatUSB interfacing software, build: 624
Running on: Microsoft Windows 10 Home (64 bit)
Serial NOR memory database loaded: 478 devices supported
Serial NAND database loaded: 0 devices supported
Parallel NOR memory database loaded: 365 devices supported
Parallel NAND memory database loaded: 295 devices supported
OTP/UV EPROM memory database loaded: 41 devices supported
Connected to FlashcatUSB XPORT, firmware version: 5.23
Detecting connected Flash device...
Initializing Parallel NOR device mode
Parallel mode successfully initialized
Attempting to automatically detect Flash device
Flash device not detected in Parallel I/O mode
When I Initially requested support for the 27C512 chip I was told it was supported and just needed a new stocket.
Pantheon said these should be in the definitions.
FlashDB.Add(New OTP_EPROM("AMD AM27C512", VCC_IF.X8_5V_12VPP, &H1, &H91, Kb512))
FlashDB.Add(New OTP_EPROM("AMD AM27C010", VCC_IF.X8_5V_12VPP, &H1, &HE, Mb001))
FlashDB.Add(New OTP_EPROM("AMD AM27C020", VCC_IF.X8_5V_12VPP, &H1, &H97, Mb002))
FlashDB.Add(New OTP_EPROM("AMD AM27C040", VCC_IF.X8_5V_12VPP, &H1, &H9B, Mb004))
At a bit of a loss for how to proceed.
For what it is worth on the latest build I can no longer engage bootloader mode. When I switch the jumper to the "FW" setting nothing happens.
I get the same thing when I try to use 27C040 or 27C020 chips.
I'm running the latest build (624) from march.
Here's my console script.
FlashcatUSB Script Engine build: 310
Welcome to the FlashcatUSB interfacing software, build: 624
Running on: Microsoft Windows 10 Home (64 bit)
Serial NOR memory database loaded: 478 devices supported
Serial NAND database loaded: 0 devices supported
Parallel NOR memory database loaded: 365 devices supported
Parallel NAND memory database loaded: 295 devices supported
OTP/UV EPROM memory database loaded: 41 devices supported
Connected to FlashcatUSB XPORT, firmware version: 5.23
Detecting connected Flash device...
Initializing Parallel NOR device mode
Parallel mode successfully initialized
Attempting to automatically detect Flash device
Flash device not detected in Parallel I/O mode
When I Initially requested support for the 27C512 chip I was told it was supported and just needed a new stocket.
Pantheon said these should be in the definitions.
FlashDB.Add(New OTP_EPROM("AMD AM27C512", VCC_IF.X8_5V_12VPP, &H1, &H91, Kb512))
FlashDB.Add(New OTP_EPROM("AMD AM27C010", VCC_IF.X8_5V_12VPP, &H1, &HE, Mb001))
FlashDB.Add(New OTP_EPROM("AMD AM27C020", VCC_IF.X8_5V_12VPP, &H1, &H97, Mb002))
FlashDB.Add(New OTP_EPROM("AMD AM27C040", VCC_IF.X8_5V_12VPP, &H1, &H9B, Mb004))
At a bit of a loss for how to proceed.
For what it is worth on the latest build I can no longer engage bootloader mode. When I switch the jumper to the "FW" setting nothing happens.